Salut, J'ai installé une imprimante sous ma FC4. (HP PSC 1610 multifonctions) Je précise que le scanner a déja fonctionner avec la meme config mais comme j'ai tous refais sur ma FC4 je passe par la. La aucun pb. Par contre je voudrais pouvoir scanner: donc j'ai suivi ceci [url]http://www.bawet.org/article.php3?id_article=48[/url] et j'ai essayer la deuxième méthode . J'ai installer tout les packages Dans le ficiher dll.conf de saned, j'ai décommenter hpoj Dans le configurateur impression, j'ai séléctionné ptal:/mlc:USB:PSC_1600 SERIES. Puis: [root@RJCSERVEUR ~]# /usr/sbin/ptal-init setup Stopping the HP OfficeJet Linux driver. ---------------------------------------------------------------------- This program manages devices controlled by the HP OfficeJet Linux driver (hpoj). It attempts to probe your computer for local parallel- and USB-connected devices, and allows you to specify network addresses for remote JetDirect-connected devices. If you experience any difficulties in detecting your device(s), then refer to the hpoj documentation for troubleshooting information. ---------------------------------------------------------------------- Currently defined device names ([*]=default): "mlc:usb:PSC_1600_series" Model is "PSC 1600 series". Serial number is "HU55DDR2HXL0". Press <Enter> alone to continue, or if you would like to delete or reconfigure one of the above-listed devices, then enter the device name to delete here ---> ---------------------------------------------------------------------- Probe for parallel-connected devices ([y]/n)? n ---------------------------------------------------------------------- Probe for USB-connected devices ([y]/n)? y Probing "/dev/usb/lp0"... Found "PSC 1600 series" with serial number "HU55DDR2HXL0". This device is already set up as "mlc:usb:PSC_1600_series". Probing "%002%001"... No device found. Probing "%001%002"... No device found. Probing "%001%001"... No device found. ---------------------------------------------------------------------- Press <Enter> alone to continue, or if you would like to add a JetDirect-connected device, then enter its dotted-decimal IP address or hostname here ---> ---------------------------------------------------------------------- Done updating device configuration files stored under /etc/ptal. If you make manual changes to those files, then be sure to run "/usr/sbin/ptal-init start" so they will take effect. ---------------------------------------------------------------------- Starting the HP OfficeJet Linux driver. mlc:usb:PSC_1600_series [root@RJCSERVEUR ~]# /usr/sbin/ptal-init start [root@RJCSERVEUR ~]# [root@RJCSERVEUR ~]# sane-find-scanner # No SCSI scanners found. If you expected something different, make sure that # you have loaded a SCSI driver for your SCSI adapter. # Also you need support for SCSI Generic (sg) in your operating system. # If using Linux, try "modprobe sg". found USB scanner (vendor=0x03f0 [HP], product=0x4811 [PSC 1600 series]) at libusb:001:002 # Your USB scanner was (probably) detected. It may or may not be supported by # SANE. Try scanimage -L and read the backend's manpage. # Not checking for parallel port scanners. # Most Scanners connected to the parallel port or other proprietary ports # can't be detected by this program. [root@RJCSERVEUR ~]# [root@RJCSERVEUR ~]# scanimage -L No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). [root@RJCSERVEUR ~]# J'ai aussi le choix entre différent drivers pr l'imprimante: PSC 1600 hpijs (ppd) ou PSC 1600 mon ficihier hp.conf (car la printer est de la marque hp) #scsi HP # Uncomment the following if you have "Error during device I/O" on SCSI # option dumb-read # # The usual place for a SCSI-scanner on Linux #/dev/scanner # # USB-scanners supported by the hp-backend # HP ScanJet 4100C usb 0x03f0 0x0101 # HP ScanJet 5200C usb 0x03f0 0x0401 # HP ScanJet 62X0C usb 0x03f0 0x0201 # HP ScanJet 63X0C usb 0x03f0 0x0601 # HP ScanJet PSC usb 0x03f0 0x4811 # # Uncomment the following if your scanner is connected by USB, # but you are not using libusb /dev/usb/scanner0 option connect-device La je ne sais pas trop les 2 lignes si je dois les décommenter ou pas. Merci de votre aide